Toilet Layout Dimensions

Bathroom design requires that a lot of fixtures be packaged into a place that’s typically on the smallish side. The International Residential Code, on which many local construction codes are based, specifies dimensions that restrict where you can place bathroom fittings, along with the National Kitchen and Bath Association presents guidelines for great bathroom design that need much more room.

Door Spacing

The IRC needs bathroom door openings be 24 inches wide. The NKBA is much more conservative, recommending the obvious opening of a doorway be at least 32 inches wide, which demands a doorway width of 34 inches. To comply with the Americans with Disabilities Act, a toilet doorway must have a clear opening of 32 inches. The NKBA additionally recommends that no door, when available, should interfere with the functioning of any other doorway or the secure and comfortable use of any toilet fixture.

Sink Location

The IRC requires clear floor space of at least 21 inches in front of toilet sinks; the NKBA recommends at least 30 inches. The IRC says a sink must be placed so its centerline is at least 15 inches from any wall and its border is no closer than 4 inches from any wall or other sink; the centerlines of dual sinks must be at least 30 inches apart. The NKBA recommends 20 inches between a sink’s centerline and the wall and 36 inches between the centerlines of dual sinks.

Tubs and Showers

The IRC specifies 24 inches of clear space in front of showers and 21 inches in front of bathtubs; the NKBA recommends increasing both dimensions to 30 inches. The minimum interior size to get a shower, according to the IRC, is 30 inches square, but the NKBA recommends at least 36 inches square. The code says that a 30-inch disc must fit inside the shower, thus a square shower with an angled doorway at one corner needs to measure about 32 inches on a side to meet that requirement.

Toilet Territory

The IRC says there should be 15 inches between the centerline of a toilet and any wall, fixture or barrier; the NKBA recommends bumping that measurement around 18 inches. Clear floor space in front of the toilet should be at least 21 inches based on the IRC, 30 inches based on the NKBA. After the toilet is enclosed in another space, that space must be at least 30 inches by 60 inches to satisfy the IRC specifications. The NKBA says that the enclosure should be at least 36 inches by 66 inches, not including any distance required by an inward-swinging door.

Ceiling Heights

A toilet’s overhead measurement might also restrict where it is possible to put fixtures inside the area. The IRC requires a minimum ceiling height of 80 inches over all fittings and over the required clear floor space in front of fittings. Showers must also have a minimum 80-inch ceiling height above their entire 30-by-30-inch interior space.

See related

How to Calculate Pavers for a Half Circle

Brick, stone or concrete pavers provide an easy do-it-yourself approach to build a patio, terrace or course. Preparing the place is more challenging than laying the pavers. There are many shapes and sizes of pavers to choose from. You want to make sure to receive enough pavers, though, because in case you need to return and purchase more, they might not be in the exact same lot and might be slightly different colors.

Determine the surface area of your pavers. Multiply the length in inches by the width in inches and divide by 144. Irregularly shaped pavers are generally sold by their typical dimensions, which can be used. Check with the supplier to get the precalculated surface area if it’s accessible.

Calculate the area of the half circle. Gauge the horizontal side of this half circle. Divide this measurement by 2 to get the radius. Square the radius. (That is, multiply the radius by the radius.) Multiply this number by 3.14. Divide by 2.

Calculate the number of pavers required by splitting the area of the half circle by the surface area of the person paver. Add 10 percent to account for waste, splitting and cutting.

See related

How to Estimate the Cost of Wood Blinds

Installing wood blinds could instantly update the appearance of a home, improve privacy, and enhance energy efficiency by preventing light. Wood blinds come in a large number of colours — with colors ranging from dark walnut to brownish chestnut to golden walnut — which will match any decor scheme, vintage, whether modern or rustic. Homeowners can gauge the cost of adding wood blinds.

Determine Quantity and End

By deciding in the event that you would like to install wood blinds in each room in your home or just on windows or in certain rooms calculate quantity. What to consider are whether you need cordless blinds, and if you would like to install coordinating valances over windows. You will need to settle on a slat dimensions for those blinds; 2 inches is the most frequent. Selecting wood blinds with features such as valances or slats that are bigger will increase costs.

Quantify for Inside-Mount Wood Blinds

At bottom, middle and the top to the closest 1/8 inch, assess the diameter of the window frame for blinds mounted within the window frame, and write down the width for your measurement. Calculate the height by measuring from the surface of the inside window frame — in the left, middle and right — down to the bottom, and write down the longest measurement, deducting 1/4 inch should you prefer the blinds don’t touch the window sill. Avoid confusion and maintain calculations organized by writing the name of every room — such as”Dining Room” or”Upstairs Bedroom” — above the corresponding window dimensions.

Quantify for Outside-Mount Wood Blinds

Where you want the blinds to expand beyond the sides of the window, for blinds find the width by measuring to the nearest eighth of an inch. Step 1 to 3 inches beyond the surfaces of the window to get optimal light blockage. Calculate the height by measuring from above the surface of the window — typically 1 to 3 inches above the window frame — down to the window sill.

Estimate Costs

As of the time of publication, the cost per blind could range from about $42 to as large as about $200, depending on the brand, colour and size, and the average cost for a professional contractor to install blinds ranges from around $140 to $225 per blind. Professional installation contains the cost of labour the blind and supplies. Homeowners may choose to install the blinds themselves to save on labor expenditures. Phone or visit hardware stores and compare the prices of installed or wooden blinds to get the cost whether self-installed.

See related

Georgian-Inspired Elegance Lives in Today's Homes

Many of us still admire the elegant proportions and soft colors which dominated English homes of the early Georgian period — that the 18th-century reigns of George I and George II. King George III was succeeded by his son, who had been prince regent and then became George IV when his daddy died. This period is much more commonly known as the regency era.

English Georgian homes were motivated by the strong classical designs of early Romans and by Italian Palladian and Pompeian decorative details. They had mild rooms with lovely proportions, large windows plus a subtle but sophisticated palette of soft blues, dusky pinks, pale grays and whites. This era has even moved entire ranges of heritage paints today, helping create a historic elegance that so many modern homeowners admire.

The typical English Georgian facade with a portico took its design from the ancient Greeks and has been used to expansive effect in the Pantheon in Rome. A porch is still a practical feature today, though we may or may not opt for this formal design.

Leone Design Studio

The Georgian with windows created rooms of proportion. While people in the period dressed their windows with sumptuous curtains and pelmets, the absence of them allows for an extremely modern aesthetic with a Georgian background.

Rachel Hazelton Interior Design

Properties had an abundance of moldings, and decorations comprised classical figures, ribbons and urns. We may not be lucky enough to own a period property, but the decorative nature of the design has been used to create many wallpapers, replica moldings and upgraded takes on classic bits — such as chandeliers.

Christine G. H. Franck, Inc..

Josiah Wedgwood was famous for his pottery and especially for his jasperware — for he, like so many of his eponymous layout sockets, took inspiration from the screenplay. Taking the shapes of Roman vessels, his bits comprised classic scenes in white on a background of those colors typical of this era.

Dijeau Poage Construction

Whether you like the traditional Wedgwood design, it has inspired generations of color schemes with while moldings — specifically, white on Wedgewood blue. You can see this timeless scheme here in a beautiful room with Georgian-style mild and ratio. Note also the hardwood flooring and Oriental rug, also typical of this era.

Patrick Sutton Associates

Thomas Chippendale, another Georgian designer and cabinetmaker, hardly needs an introduction, as his work continues to inspire furniture design today. His style has an inherent simplicity with Chinese influences that are exotic. Today his work is used in the design of balustrades and railings.

From the old era, furniture has been made from wood, such as walnut; wood has been also introduced from Spain and then from Central America. Nowadays many of us still love rich, dark wood. Here it adds warmth and elegance into a softer Georgian color palette.

See related

Do Queen Air Mattresses Use Full-Size Sheets?

Queen-sized air mattresses require queen-size sheets, since full-size sheets only won’t fit onto a queen-size mattress in any way. Full-size sheets are designed to fit beds which measure 54 inches across the width and 75 inches down their length. Queen air-mattresses are more than that by 3 to 5 inches, but most can also be 6 inches broader than full-sized or double mattresses.

All in the Dimensions

When you buy sheets to get a queen-sized air mattress, then don’t neglect to measure the height and duration of it. As an instance, a 9-inch high queen-size air mattress generally has the exact dimensions as that of a typical queen mattress, but if the mattress rises its height, it often loses 2 ins on length, dropping in the standard 80 inches to 78 inches. However you measure it, you require queen-size sheets to get a queen-size air mattress.

See related